Shareware Overload Trio 2

home *** CD-ROM | disk | FTP | other *** search

/ Shareware Overload Trio 2 / Shareware Overload Trio Volume 2 (Chestnut CD-ROM).ISO / dir24 / logeqfv6.zip / LOG-EQF.DOC < prev next >

Wrap

Text File | 1994-04-02 | 140KB | 2,489 lines

PAGE i Log-EQF is distributed as Shareware. Continued use of this program requires that you become a Registered User. See page v of this manual for registration details. ------------ USER'S GUIDE ------------ ╔═══════════════════════════════════╗ ║ ║ ║ ╦ ╔═╗ ╔══ ╔══ ╔═╗ ╔══ ║ ║ ║ ║ ║ ║ ══ ╠═ ║ ║ ╠═ ║ ║ ║ ║ ║ ║ ╦ ║ ║ ║ ║ ║ ║ ╩══ ╚═╝ ╚═╝ ╚══ ╚═╠ ╩ ║ ║ Version 6.00 ╨ ║ ║ Copyright (C) 1989 - 1994 ║ ║ Thomas Dandrea - N3EQF ║ ║ ║ ║ -ALL RIGHTS RESERVED- ║ ║ ║ ╚═══════════════════════════════════╝ Tom Dandrea, N3EQF 396 Sautter Drive Coraopolis, PA 15108-9244 USA - EQF Software - (412) 457-2584 _______ ____|__ | (R) --| | |------------------- | ____|__ | Association of | | |_| Shareware |__| o | Professionals -----| | |--------------------- |___|___| MEMBER Throughout this manual any commercial trade names mentioned are either trademarks or registered trademarks of their developers. Use of these trade names does not indicate an endorsement by the trademark owners. --------------------------------CONTENTS----------------------- PAGE ii Definition of Shareware & Disclaimer...................iv Registration and Support & Ombudsman....................v 1. Log-EQF Overview......................................1.0 2. Installation..........................................2.0 SYSTEM REQUIREMENTS........................2.0 INSTALLING Log-EQF.........................2.0 FILES REQUIRED FOR OPERATION...............2.1 3. Program Startup and Customization.....................3.0 CONFIGURATION SETUP........................3.0 LOADING LOGBOOK INFORMATION FROM FILES.....3.4 QUICK STARTUP OF Log-EQF...................3.6 USING "AMSOFT", "HAMCALL", "SAM", or QRZ!..3.7 4. Main Menu Commands....................................4.0 VIEW IN DETAIL.............................4.1 QUICK VIEW.................................4.2 PRINT LOGBOOK..............................4.3 QSL LABELS.................................4.4 LOG - AUTOMATIC............................4.5 LOG - MANUAL...............................4.9 EDIT.......................................4.11 LOAD.......................................4.12 SORT.......................................4.13 SEARCH.....................................4.15 NORMAL/CONTEST SELECTION...................4.16 RUN ANOTHER PROGRAM........................4.17 SETUP......................................4.18 EXIT.......................................4.18 5. Contest Operation.....................................5.0 INTRODUCTION...............................5.0 CONFIGURATION SETUP........................5.1 OPERATION DURING THE CONTEST...............5.4 OPERATION AFTER THE CONTEST................5.6 6. Radio Interface Operation.............................6.0 7. Terminal Node Controller (TNC) Operation..............7.0 8. CW Keyer Operation....................................8.0 9. External Control via LPT port.........................9.0 10. Maintenance of the DX Prefix Library.................10.0 11. In Case of Trouble...................................11.0 PAGE iii [This page intentionally left blank] DEFINITION OF SHAREWARE PAGE iv ----------------------- Shareware distribution gives users a chance to try software before buying it. If you try a Shareware program and continue using it, you are expected to register. Individual programs differ on details -- some request registration while others require it, some specify a maximum trial period. With registration, you get anything from the simple right to continue using the software to an updated program with printed manual. Copyright laws apply to both Shareware and commercial software, and the copyright holder retains all rights, with a few specific exceptions as stated below. The main difference is in the method of distribution. The author specifically grants the right to copy and distribute the software, either to all and sundry or to a specific group. Shareware is a distribution method, not a type of software. You should find software that suits your needs and pocketbook, whether it's commercial or Shareware. The Shareware system makes fitting your needs easier, because you can try before you buy. And because the overhead is low, prices are low also. Shareware has the ultimate money-back guarantee -- if you don't use the product, you don't pay for it. DISCLAIMER - AGREEMENT ---------------------- Users of Log-EQF must accept this disclaimer of warranty: "Log-EQF is supplied as is. The author disclaims all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The author assumes no liability for damages, direct or consequential, which may result from the use of Log-EQF." Log-EQF is a "shareware program" and is provided at no charge to the user for evaluation. Feel free to share it with your friends, but please do not give it away altered or as part of another system. The essence of "user-supported" software is to provide personal computer users with quality software without high prices, and yet to provide incentive for programmers to continue to develop new products. If you find this program useful and find that you are using Log-EQF and continue to use Log-EQF after a reasonable trial period, you must make a registration payment of $25 to N3EQF. The $25 registration fee will license one copy for use on any one computer at any one time. Anyone distributing Log-EQF for any kind of remuneration must first contact N3EQF at the address above for authorization. This authorization will be automatically granted to distributors recognized by the (ASP) as adhering to its guidelines for shareware distributors, and such distributors may begin offering Log-EQF immediately (However N3EQF must still be advised so that the distributor can be kept up-to-date with the latest version of Log-EQF). You are encouraged to pass a copy of Log-EQF along to your friends for evaluation. Please encourage them to register their copy if they find that they can use it. All registered users will receive a copy of the latest version of the Log-EQF system. REGISTRATION AND SUPPORT POLICY PAGE v ------------------------------- To become a registered user of Log-EQF, you must send a $25 fee to the author at the address below: ┌───────────────────────────────┐ │ Tom Dandrea, N3EQF │ │ 396 Sautter Drive │ │ Coraopolis, PA 15108-9244 │ └───────────────────────────────┘ To register, use the form shown on the following page, or provide the information below in any readable format to N3EQF: - Current version number of Log-EQF you're using. - The type of floppy disk you require (i.e., 360K) - Your amateur callsign. - Complete mailing address. When you become a registered user, you are provided the following: 1. The current version of Log-EQF will be sent upon receipt of payment. The program will be supplied on the floppy type you specify. 2. In addition to the Log-EQF program, you will be provided with two utility programs for importing logbook files from other logging programs into Log-EQF, and for tracking DXCC award progress. 3. You will be automatically notified when major revisions to Log-EQF are released. 4. Technical support is available at the above address and phone number, for a minimum period of 6 months after the registration date. N3EQF makes every attempt to correct any problems reported about the use of the Log-EQF program. I also welcome constructive criticism and suggestions for improvement. The current version of Log-EQF rep- resents the collective input received from registered users over more than four years. OMBUDSMAN --------- Tom Dandrea, N3EQF, is a member of the Association of Shareware Professionals (ASP). ASP wants to make sure that the shareware principle works for you. If you are unable to resolve a shareware-related problem with an ASP member by contracting the member directly, ASP may be able to help. The ASP Ombudsman can help you resolve a dispute or problem with an ASP member, but does not provide technical support for members' products. Please write to the ASP Ombudsman at 545 Grover Road, Muskegon, MI 49442 or send a CompuServe message via CompuServe Mail to ASP Ombudsman 70007,3536. REGISTRATION FORM PAGE vi Log-EQF 6.00 Registration and Order Form Your Name: _______________________________Callsign:_____________ Address: _______________________________________________________ City: _____________________________ State/Province: ____________ Country: ____________________________ Zip/Postcode: ____________ ----------------------------------------------------------------- Log-EQF Registration ...............................: $25.00 * For orders outside of the U.S., Canada, and Mexico, please add $3.00 shipping and handling. Please indicate the disk size you prefer: .... __5 1/4" __3 1/2" Payment must be in U.S. funds, drawn on a U.S. bank. Pennsylvania residents please add 6% sales tax. Please send the completed form, along with a check or money order to: EQF Software Technical Support: (412) 457-2584 Tom Dandrea, N3EQF 396 Sautter Drive (Evenings & weekends, Coraopolis, PA 15108 U.S.A. or leave a message). ------------------------------------------------------------------- You can also order with your Master Card or Visa from WestWorld Computer Services: By mail: By Email: -------- --------- WestWorld Computer Services Genie: WESTWORLD 3755 Avocado Blvd Suite 304 CompuServe: 70574,450 La Mesa, CA 91941-7301 America On-line: WESTWORLD Prodigy: JSPB88A Delphi: WESTWORLD1 By calling: 800-995-1605 (24 hours) ----------- From overseas: 619-685-7291 (24 hours) -------------- FAX to: 619-558-7850. ------- THESE NUMBERS ARE FOR ORDERING ONLY. EQF Software can NOT be reached at those numbers. To contact N3EQF for information about anything other than to place a credit card order or to receive authorization for returns, call Tom Dandrea at 412-457-2584, or write N3EQF at 396 Sautter Drive, Coraopolis, PA. OVERVIEW PAGE 1.0 1. LOG-EQF OVERVIEW -------------------- The Log-EQF program helps you maintain a complete and accurate station logbook with minimal effort. Log-EQF will function as a full-featured electronic logbook when used alone on a personal computer. If the pro- gram is used on a computer that is connected to a transceiver interfaced via an RS-232C serial port, many additional automatic logging and con- trol features are enabled. Your TNC is supported, with PacketCluster (tm), file upload and download, and a monitor window on the logging screen. Below are some of the features of Log-EQF: - DAILY LOGBOOK (STAND-ALONE) --------------------------- - Easy to use menus for all operations, complete with mouse control. - Full-screen entry of logbook information in any order desired. - Easy edit or deletion of any logbook entry. - Automatic date and time logging with built-in UTC conversion. - Quick reports of DXCC Zone and Continent info from callsign prefix. - Beam Headings displayed from DXCC prefix of callsign. - Abbreviated or complete display of logbook entries. - Ability to search logbook for a pattern in any entry field. - Able to sort logbook files by any field. - Print all or part of logbook, either in abbreviated or detailed form. - Print QSL labels with personalized message line. - Customized screen colors and on-screen display of your callsign. - Run other programs while Log-EQF stays in memory (EMS if installed). - Monitor PACKET or any other TNC operation while logging. - Interfaces with SAM, HAMCALL, and AMSOFT for auto name and QTH entry. - 10-minute identification reminder. - CW Memory Keyer outputs to LPT (parallel) or COM (serial) ports. - External device control over LPT port eight data lines. - CONTEST MODE ------------ - Fast dupe checking with displayed details. - Optional automatic generation of serial numbers for exchange. - Optional printout of each entry as it's logged (data security). - Generate Dupe sheets. - Print entry logbook w/ auto QSO and multiplier totals (user-defined). - ASCII disk files created for dupe sheets and contest logs. - Partial callsign check. - On-screen QSO rate and lapse time displays. - RADIO INTERFACE --------------- - Automatic display and logging of radio mode and frequency. - Control over radio VFO and mode from log entry screens. - "Hot key" access to the optional Rig-EQF Kenwood rig control program. - On-screen display of two VFOs and "TRANSMIT" for Kenwood radios. INSTALLATION PAGE 2.0 2. INSTALLATION ---------------- - SYSTEM REQUIREMENTS ------------------- - IBM PC, XT, AT, PS/2 or compatible. - DOS 3.0 or higher. - 512K memory (The program executable requires about 200K). - Monochrome or color monitor (no graphics adapter required). - 1 floppy drive and/or a hard drive (hard disk drive recommended). - (optional) 1 serial comm port (COM1-COM4) for radio interface. - (optional) 1 serial comm port for Terminal Node Controller (TNC). - 1 parallel printer port and printer recommended. - Mouse (Microsoft compatible), bus mouse if all COM ports are used. If a radio is to be interfaced to your computer for use with Log-EQF, it must be connected to the computer's serial port following the radio manufacturer's documentation guidelines. For many radios, a TTL/RS232C converter must be used between the computer and radio. See Chapter 6 of this manual for more information about radio computer interfacing. You may also use a Terminal Node Controller (TNC) with Log-EQF. Log-EQF is compatible with any TNC designed to work with standard TTY or ANSI terminal emulation communication software. No attempt is made to control a TNC in host mode. - INSTALLING LOG-EQF SOFTWARE --------------------------- Before proceeding, make a WORKING copy of the Log-EQF floppy. (Refer to your DOS manual for information about copying programs). USE THE WORKING COPY YOU CREATE TO INSTALL LOG-EQF, AND MAINTAIN YOUR ORIGINAL DISK IN A SAFE PLACE! Log-EQF comes in compressed format, so that all the required files will fit onto a single 360K floppy. A file called INSTALL will unpack all the necessary files onto the disk or directory you specify. If you did not receive an INSTALL program, the files for Log-EQF can be installed by copying file LOGEQF.EXE into a new disk directory. Then just type: LOGEQF <Enter> Note that a disk directory (usually called LOG-EQF) must be created using DOS before installing Log-EQF in this manner. NOTE: After installing Log-EQF, check your CONFIG.SYS file in the root directory for a statement that says: FILES = 20 (or higher than 20). This prevents an error from occurring in Log-EQF, when multiple files are open at the same time. Consult your DOS manual for further information. INSTALLATION PAGE 2.1 - FILES REQUIRED BY LOG-EQF ------------------------- The following is a list of files which are necessary for all functions of Log-EQF to operate, along with their description: * LOG-EQF.EXE Main executable logbook module. * LOG-EQF.CNF User-defined configuration parameters (created the first time LOG-EQF is run). DUPE-EQF.EXE Dupe-sheet and contest log generation module. CONTEST.?? Contest configurations for up to 23 contest events. * PREFIX.LIB DXCC Prefix Library (Also used for beam headings). * STATES.LIB Beam Heading file for STATE field. LOG-EQF.DOC Documentation File (User's Guide) for Log-EQF. 5.KEY-10.KEY Macro files (OPTIONAL) for use with TNC function keys. SHELL1?.BAT BATCH files to be executed by the <F11> and <F12> keys. ????????.RIG Radio configuration files (OPTIONAL) for interfacing. LOG-EQF.FRQ Frequency range table (OPTIONAL) for external control. KEYER.DAT Memory storage for CW Keyer. BACKUP.BAT BATCH file that specifies what utility you want to use for creating backups of Log-EQF logbooks. LOG.BAT BATCH file for starting Log-EQF with the SAM callsign database. Edit this file to suite your installation. If disk space is limited, and you do not require contest operation or the DXCC or file-conversion utilities, you can install only those files marked with an asterisk (*) on your disk. DUPE-EQF.EXE and CONTEST.?? can also be omitted if you will not be working contests with Log-EQF. You can name logbook files whatever you like. The only limitation on file- names are the restrictions imposed by DOS; file names can be no longer than 8 characters. Log-EQF automatically adds the ".LOG" file extension to the end of the logbook name you define. When you enter a logbook name from within Log-EQF, you do not have to type the ".LOG" extension. To load the sample logbook, for example, you type in only "SAMPLE". Besides the ".LOG" logbook files, Log-EQF also creates a notepad file using the same name as your logbook, but with ".NOT" as the file extension. The notepad file contains 480 characters of text for any QSO which you decide to write a notepad. CONFIGURATION PAGE 3.0 3. PROGRAM STARTUP AND CUSTOMIZATION ------------------------------------- - CONFIGURATION SETUP ------------------- The first time you run Log-EQF, you will be directed automatically to the Log-EQF configuration setup menu. If you wish to change a previously- defined configuration, you can access the setup menu by selecting it from the Log-EQF Main menu. ------------------------------------------------------------------------- Log-EQF Copyright (C) 1994, N3EQF SETUP MENU - Hit <Esc> to exit ------------------------------------------------------------------------- Callsign ->N3EQF Latitude (N = +)? 40.5 [Degrees as a decimal number] Longitude (E = +)? -80.1 Hours to add to clock time for UTC ->5 [Enter 0 if computer = UTC] POWER level used most often ->100 Logbook Name used most often ->LOGBOOK First Program Name for SHELL->GOLIST %C Second Program Name to SHELL ->GEOCLOCK <F5> = PRINT COLOR: 15 <F1> = DATE FORMAT: mm-dd-yy <F6> = SCREEN COLOR: 1 <F2> = PRINTER TYPE: Graphics <F7> = BORDER COLOR: ON <F3> = CW PORT: LPT1 <F8> = EXTERNAL CONTROL: OFF ╒═ <F4> = RADIO: KENWOOD ════════════╕╒═ <F9> = TNC ═════════════════════╕ │ COM port number ->2 ││ COM port number ->1 │ │ Baud rate ->4800 ││ Baud rate ->9600 │ │ Parity (E/O/N) ->N ││ Parity (E/O/N) ->N │ │ Data bits (7/8) ->8 ││ Data bits (7/8) ->8 │ │ Stop Bits (1/2) ->1 ││ Stop Bits (1/2) ->1 │ │ Base Address ->2F8 ││ Base Address ->3F8 │ │ IRQ ->3 ││ IRQ ->4 │ ╘════════════════════════════════════╛╘══════════════════════════════════╛ For each item on the menu, the values to the right of the arrow can be changed. To do that, position the screen cursor to the line desired by using the Up or Down arrow keys. When the cursor is on the desired line, type in the new value and hit <Enter>. CALLSIGN is used at the top of most screen displays and printouts. LATITUDE/LONGITUDE is used by the program to calculate beam headings. Enter your station's latitude and longitude in degrees for both items. Log-EQF defaults to a lat/lon in the central United States, until you enter the location of your station. CONFIGURATION PAGE 3.1 POWER LEVEL is the value automatically entered into your logbook for transmitter power. You can override this default value at any time by typing over the existing value. HOURS TO ADD FOR UTC controls how the date and time for Log-EQF logbook entries is determined. If the response to the menu item is "0", then the time used for each log entry will be exactly the same as your computer's clock time. If you enter any other number for this menu item, that number will be ADDED (SUBTRACTED, if you enter a negative number), to the computer clock to calculate the date and time used for logging entries. This item enables you to keep your computer clock on local time, and have your logbook times in UTC. LOGBOOK NAME is the name of the logbook file you will want to use for most of your logging. The name you enter here will appear when you run Log-EQF each time, so you don't have to type it in yourself. If you leave this setup item blank, the program will make up a name for you, based on the current year, such as "1990LOG". You can type in a new name at any time, no matter what option you decide on for this item. <F4> RADIO and <F9> TNC are used to select the communication parameters to be used by your radio and TNC, respectively. When <F4> is selected, a menu presenting available radio manufacturer/model numbers will appear. If your rig appears on the menu, just highlight the correct selection and hit <Enter>. If your radio is computer-ready and doesn't appear, see Chapter 6 for instructions on configuring Log-EQF. You do not need to select a specific model for your TNC, since Log-EQF acts as a generic "dumb terminal" to these devices. CW PORT sets the COM (serial) or LPT (parallel) port to use for sending CW to your rig. The CW controller inside Log-EQF uses the same interface pins as the CT and NA programs. COM PORT NUMBER tells Log-EQF whether you are using a radio and/or TNC. Enter a 0 in the respective box if you are not using a radio or TNC, or enter a number between 1 and 4 for the serial port being used. The TNC and radio must be on separate ports of course. BAUD RATE sets the communication rate between your computer and your radio and/or TNC. Your TNC and radio must be set to match the value you enter here. Typical baud rates are 1200 and 4800. If your TNC is set for AUTO baud rate, it will be necessary for you to go to the split-screen terminal emulation from the AUTOMATIC or MANUAL LOGGING screen using <F8>, and then "wake up" the TNC when prompted. Consult the manufacturer's documentation for directions on setting baud rate for your particular model. PARITY, DATA BITS, STOP BITS are set to match the communication parameters required by your radio and TNC. The default values for No parity (N), 8 data bits, and 1 stop bit are the most common. NOTE: Your TNC should also be set for ECHO ON, so that characters you type will be displayed. CONFIGURATION PAGE 3.2 ADDRESS and IRQ must be set to match your computer's configuration for the serial (COM) port(s) in use by your radio and TNC. Log-EQF will enter values automatically for these parameters any time you change the port number. If you are not sure what the address and interrupt parameters are for your computer, consult the documentation for your system or check the settings in use by any other programs you use for COM port communication. PROGRAM NAMES for SHELL is used to enter program names which can be accessed from Log-EQF's Main Menu. You can use this feature to access often-used programs through Log-EQF. If the program you want to run cannot be located in the same directory as Log-EQF, you can prepare a small file called a BATCH file to execute it. Your BATCH file (consult your DOS manual for information about creating BATCH files) would perform a DOS "CD" command to change directories to the one where your program resides, and then "CALL" that program. Once you have created your BATCH file, store it in the same directory as Log-EQF, and specify the BATCH file's name on this item on the SETUP menu. You can append the program name you supply for the SHELL with special parameters which are passed to that program from Log-EQF's logging screen. The available parameters are %C, %F, %M, %T, and %H, for Callsign, Frequency, Mode, Track, and Heading, respectively. If you supply DX-EQF %C for the program name to SHELL to, and you just entered 9X5AA as the callsign on the Log-EQF logging screen, the DX-EQF program module (available free to Registered Users) will check your DXCC status for that country automatically. Another possibility would be to use the %C parameter with the name of a "CALLBOOK" routine, to look up QSL information for the station you just worked. If you have about 300K of Expanded Memory available on your computer, Log- EQF will attempt to relocate itself into that memory space, so that conventional "DOS" memory is freed for use by other programs. To find if Expanded Memory is in use with Log-EQF, select SHELL to DOS, and check for a message "EMS in use" at the upper right corner of the screen. Consult your DOS manual for configuration of memory drivers such as "EMM386.EXE". DATE FORMAT is accessed using the <F1> key, and can be used to change the format of the date entries in the log. A menu will be displayed which presents the available formats. PRINTER TYPE can be standard, graphics, or a disk file. If your printer is an Epson, or emulates the Epson graphics character set, select "GRAPHICS". If your printer prints strange characters instead of lines from Log-EQF, select "STANDARD". The third selection is labeled "DISK FILE". You may use this option to direct print operations into a disk file, for use by other programs (such as word processors) for formatting. Log-EQF will ask you to enter a file name to be used each time you begin printing. CONFIGURATION PAGE 3.3 If your system has a color adapter and monitor, you can customize colors which Log-EQF displays for background and characters. Hit the <F5>, <F6>, and <F7> keys on your keyboard, and the display will update to show you the current color selection. - When all parameters on the configuration menu screen are set, hit the <Esc> key again to save all the values to a disk file called LOG-EQF.CNF. LOADING PAGE 3.4 - LOADING LOGBOOK FILES --------------------- Once the configuration setup is complete, you will want to either load an existing logbook, or start a new logbook. The following menu is displayed by Log-EQF: ╒═══════════════════════ N3EQF Amateur Radio Logbook ═════════════════════╕ │ Entries In Log = 2091 Last Entry = VP25EI │ ╘═════════════════════════════════════════════════════════════════════════╛ ╒═══ LOAD LOGBOOK ENTRIES ════════════════════════════════════╕ │ │ │ │ │ Enter an existing or new log name below, or hit <─┘ │ │ to load the file shown. │ │ │ │ Enter logbook name: NEWLOG │ │ │ ╘═════════════════════════════════════════════════════════════╛ ╒═════════════════════════════════════════════════════════════╕ │ <F1> = CONTEST / DXpedition MODE │ │ <F2> = CONFIGURATION │ │ <F3> = SHOW AVAILABLE LOGBOOKS │ │ <F4> = RENAME CUSTOM FIELDS │ │ <F5> = MAKE BACKUP OF NEWLOG FILES │ ╘═════════════════════════════════════════════════════════════╛ ═════════════════════════════════╡ Memory enough for 22701 more QSOs ╞══ Log-EQF will prompt you to "Enter logbook name", display a log file name, and then wait for your response. If the name that is displayed is the logbook you want to use, just hit <Enter>. (This is what is known as a DEFAULT value, meaning if you don't type in new information, the program uses the old information that is displayed on the screen). If this log already exists, the program will read all the entries from that file. If the log name is a new one, you will be asked if you want to create a new log file on the disk. If you want to use a file name other than the default, you may type it in and then hit <Enter>. Note that logbook names cannot be longer than 8 characters (plus ".LOG"). A sample logbook file should be present on your Log-EQF disk. This file may be used to demonstrate the features of Log-EQF, and for experimentation until you become familiar with the program's operation. To load this sample file, type "SAMPLE" at the prompt. LOADING PAGE 3.5 The default file name is determined by information supplied by you from the Configuration Setup menu. If you supplied a logbook file name on the Configuration Setup menu line for "Logbook name most often used", then that name will be used by Log-EQF each time you run the program. If you didn't supply a default name (left the item blank), the first 4 characters of the file name are taken from the last 4 characters of the computer clock's date variable. The last 3 characters are always "LOG". If the current date is 1994, the default file name is "1994LOG". NOTE: If you wish to load data from a disk other than the one running Log-EQF currently, you may proceed the file name with the disk assignment. For example, if Log-EQF is being run from hard drive C, and you wish to load logbook data from floppy drive A, file 1994LOG, then you would enter "A:\1994LOG" from the prompt. This will remain the logbook file which is viewed, edited, sorted, searched, or entered into by Log-EQF, until you enter a new name. You may also access another logbook by hitting the <F3> function key. This will display all available logbooks in the current disk directory, and allow you to choose the one to be loaded. You can also view the log files in another directory from this screen. The <F4> function key has a very special purpose. With it, you can customize the logbook to contain two fields you name yourself. These fields are called "TRACK" and "INFO", unless you call them something else. You could rename a field as "COUNTY", or "10-10", or any other name to describe something you want to keep track of in your logbook. Whatever name you give it, this field will stay associated with the logbook to be loaded. You can name different fields for different logbooks, depending on your operation. The <F5> key gives you an easy way to backup the current (displayed) logbook files onto either a floppy drive or another disk directory on the current drive. When <F5> is pressed, you will be asked where you want the backup files to be copied. You can enter "A:" or "B:", for instance, to have the backup created onto a floppy disk. Log-EQF will copy all the files associated with the logbook name currently entered to the disk or directory that you specify. Log-EQF uses a file called BACKUP.BAT, which must be present to in the same directory as Log-EQF. You may customize this BATCH file to work with your favorite backup utility. The first parameter passed to the batch file is the source file specification, followed by target disk drive specification. See your DOS User's Guide for instructions on creating batch files. QUICK START PAGE 3.6 - QUICK STARTUP OF LOG-EQF ------------------------ A shortcut is available to allow you to start the program and load the logbook file faster. To take advantage of this feature, you need only know in advance what logbook name you are going to be using. Instead of typing "Log-EQF" and hitting <Enter>, follow the program's name with a space, and the name of your logbook file. For example, if you want to do a "quick startup" using the SAMPLE logbook, type: LOG-EQF SAMPLE <Enter> When you use the "quick startup" method, the program will not display the Welcome Screen or pause for you to hit a key to continue. If you are using a radio interface, the radio and interface should be turned on before you start the program. You will also not be prompted to enter the name of logbook file to be loaded. Instead, Log-EQF will auto- matically load the logbook you entered when you started the program. When the logbook loading is complete, the Main Menu will be displayed, and program operation will revert to normal. You may also specify the program to startup in CONTEST mode by supplying " /C" after the log filename from the command line. The following line would cause Log-EQF to present the contest SETUP MENU and then load the file TEST.LOG: LOG-EQF TEST /C <Enter> Another command line option forces Log-EQF to use the display options for MONOCHROME computer displays. To do this, add " /M" after the other command line parameters. For example: LOG-EQF TEST /C /M <Enter> One remaining option can be used to associate the configuration file used by Log-EQF with the logbook file. (Normally, Log-EQF reads a file called LOG-EQF.CNF for configuration information). To load a logbook called SPECIAL, and create a configuration file called SPECIAL.CNF, type: LOG-EQF SPECIAL /L <Enter> CALLSIGN DATABASE SYSTEMS PAGE 3.7 - CALLSIGN DATABASE SYSTEMS: "AMSOFT", "HAMCALL", QRZ!, or "SAM" ---------------------------------------------------------------- 1). "SAM" by RT Systems (either disk or CD-ROM): Log-EQF will interface with the SAM Amateur Radio Callsign Database System, by RT Systems, so that the NAME, CITY, STATE, and optionally the COUNTY logbook fields will be filled in automatically as soon as a CALLSIGN is entered in the log. To enable this feature, you must use the "Application Program Interface" routine called SAMAPI for the disk-based SAM, or SAMAPICD for the CD-ROM verion of SAM. The correct TSR is supplied with the SAM product. The TSR program must be started before running Log- EQF. When you start Log-EQF, the SAM interface will automatically be enabled. There is nothing else required to enable this feature. A startup batch file called Jr.BAT has been provided. To start Log-EQF running and automatically enable SAM, just type "LOG". Please consult your SAM User's Guide for specific information about SAMAPI, or contact RT Systems. 2). "HAMCALL" by Buckmaster Publishing, "AMSOFT World of Ham Radio", or "QRZ!" by AA7BQ: Log-EQF will automatically interrogate your system to see if these CD-ROM systems are installed each time Log-EQF is started. Therefore, if you want to have Log-EQF retrieve the name and QTH information from eiter database, your CD-ROM must be on-line with the disk installed before you start Log- EQF. To utilize HAMCALL, AMSOFT, or QRZ!, just hit the <F5> INFO key on the logging screen. MAIN MENU PAGE 4.0 4. MAIN MENU COMMANDS ------------------ After a logbook has been loaded (or created), a menu will be displayed with 14 items for selection. To select an item, use the arrow keys or the mouse to change which item is highlighted. When the desired item is highlighted, hit the <Enter> key to select that item. The Log-EQF Main Menu screen appears below: ╒═══════════════════════ N3EQF Amateur Radio Logbook ═════════════════════╕ │ Entries In Log = 2091 Last Entry = VP25EI │ ╘═════════════════════════════════════════════════════════════════════════╛ ┌───────────────────────────────────┬─────────────────────────────────────┐ │ VIEW in DETAIL entries in logbook │ LOAD QSOs from another logbook │ │ │ │ │ QUICK VIEW entries in NEWLOG │ SORT logbook file by any field │ │ │ │ │ PRINT logbook record pages │ SEARCH log - Print/File/QSL options │ │ │ │ │ QSL LABELS: Setup and Print │ NORMAL mode - switch for CONTEST │ │ │ │ │ LOG new entries - AUTOMATIC mode │ RUN ANOTHER PROGRAM │ │ │ │ │ LOG new entries - MANUAL mode │ SETUP program configuration │ │ │ │ │ EDIT an entry - based on callsign │ EXIT from program │ └───────────────────────────────────┴─────────────────────────────────────┘ ╔═══════════╗ ║ 22:34:10 ║ ═════════════════════════╡ Log-EQF MAIN MENU ╞════════════════╚═══════════╝ Selection of a menu item will, depending on the type of operation selected, display another menu, prompt you for some further information, or switch the selected item to display some other item. No matter which item is selected, hitting the <Esc> key will again display the Main Menu. The following paragraphs discuss the operation of each item on the Main Menu. VIEW IN DETAIL PAGE 4.1 - VIEW in DETAIL entries in logbook --------------------------------- Selecting this item will display the first screen of entries contained in the current logbook. One screen page in this mode contains 5 QSO's, unless notepad entries are present. The number of QSO's on each screen is automatically adjusted by the program to display notepad entries. The format of this display consists of at least three lines for each QSO, showing the complete details for each entry: CALLSIGN CITY DATE START TIME SENT REPORT QSL NAME STATE FREQ. END TIME RECEIVED RPT MODE POWER QSO # TRACK COUNTRY INFORMATION... As soon as the first screen page of entries is displayed, several options are available, and these options are explained on the bottom line of the screen. If NOTEPAD information exists for a logbook entry, that information will be displayed immediately following the standard three-line entry. Selecting the <F1> function key activates the EDIT option. The program will prompt you to enter a QSO number for the log entry you wish to edit. Selecting the <Esc> key causes the VIEW in DETAIL mode to be stopped, and the Main Menu will be displayed again. The <Page Up> and <Page Down> keys may be used to scroll through the next five entries, or the previous five entries in the log. The <Up Arrow> and <Down Arrow> keys have the same effect, except the log entries scroll forward and backwards one at a time. At any time while scrolling through the log entries, you may select <Esc> to return to the Main Menu. QUICK VIEW PAGE 4.2 - QUICK VIEW entries in logbook ----------------------------- Selecting this item causes display of a page containing abbreviated, one- line entries for the first 23 QSO's in the current logbook. This mode allows you to browse quickly through the log. The format of each entry line is: DATE TIME CALLSIGN FREQ MODE SENT RCVD QTH NAME QSL To advance to the next page of 23 QSO's, just hit a key. To start over again at the first page of 23 QSO's, hit the <Home> key. The <End> key may be used to jump to the end of the logbook. The <Up Arrow>, <Down Arrow>, <Page Up>, and <Page Down> keys may be used to scroll through the log entries in either direction. To return to the Main Menu, hit the <Esc> key. PRINT LOGBOOK PAGE 4.3 - PRINT logbook record pages -------------------------- This menu item allows you to print some or all of the current logbook, using either the same format as is displayed on the screen during the VIEW IN DETAIL option, or the shorter format as used during the QUICK VIEW option. A two-window menu appears, enabling you to either print all the QSO's in the logbook, or to print any series of QSO's. To select an item in the top window, highlight it by using the arrow keys and hit the <Enter> key. ╒════ Logbook Print ══════════════════════════════╕ │ │ │ Print ALL QSOs in the logbook file │ │ │ │ Print QSOs from number [ 1 ] to [ 2459 ] │ │ │ │ Print from dates [10Mar71 ] to [20Nov92 ] │ │ │ │ Print any QSOs marked `P' in QSL STATUS │ │ │ ╘═════════════════════════════════════════════════╛ ╒════ Selected Format ════════════════════════════╕ │ │ │ SINGLE LINE... hit <F1> for DETAILED │ │ │ ╘═════════════════════════════════════════════════╛ When the "Print QSO's from number [ ] to [ ]" option is selected, enter the first QSO number, hit <Enter>, then enter the last QSO number to be printed. The default numbers for these are the first and last entries in the logbook. You may alter either one of both of these numbers or just hit <Enter> to accept a default value. Another menu item allows you to print entries between any two dates. To switch between the short and long print formats, use the <F1> key until the desired format type is displayed in the bottom menu window. After you have made your selections, hit the <Enter> key. The program will prompt you to prepare the line printer and hit any key to begin printing. The printed page is setup to accommodate standard 8-1/2 x 11 inch paper. If you elect to keep your printed logbook in a 3-ring binder, a few QSO numbers may be lost when the paper is punched, since the numbers appear on the extreme left edge of the page. Most printers will allow you to shift the paper position to the left far enough to allow the logbook pages to be punched without interfering with the printed information. QSL LABELS PAGE 4.4 - QSL LABELS output to printer ---------------------------- Select this item to print QSL labels for all or part of the QSO's in the current logbook. The selections available for this option are the same as for the "PRINT logbook" option described above. ╒═ Label Size (inches) ═══════════════════════════╕ │ 5-line 3.5 x 15/16 1 across │ │ 5-line 3.5 x 1.5 1 across │ │ 1-line 5 x 7/16 1 across │ │ 5-line 4 x 1 2 across │ │ 5-line 2-5/8 x 1 3 across │ ╘═════════════════════════════════════════════════╛ ╒═════════════════════════════════════════════════╕ │ <F1> Style: Standard │ │ <F2> Margins: Top = 0 lines │ │ Left = 0 rows │ │ <F3> Page eject after 0 labels │ │ <F4> Print a TEST LABEL │ ╘═════════════════════════════════════════════════╛ The "LABEL OPTIONS" menu allows you some controls over the appearance and size of the QSL labels to be printed. There are two basic styles; one with 5-lines of text to be printed, and one which prints the QSL info on a single line. The single line text is printed on a label measuring 5" x 7/16", in the following format: CALLSIGN DAY MONTH YEAR TIME BAND RST MODE This 1-line style will easily fit below the labeled columns on pre-printed QSL cards. The 5-line styles fit on larger labels, either "1 across" (also known as continuous stock), or as "2 across" or "3 across" labels for use with laser printers. A "graphic" selection is available, which will print solid lines and double-wide callsign fonts if your printer is capable of printing graphics characters. NOTE: If you use a laser printer, make sure your printer is set manually for 60 lines of text for a 10-inch page length, or 6 lines per inch. If you need to adjust the top or left side margins to align labels with your printer, select <F1> to enter appropriate margins, and <F2> to enter the number of labels on each page. Use <F3> to test the current settings. Another option for QSL label printing concerns automatic updating of the QSL status field for each log entry being confirmed. If you select this option when prompted, Log-EQF will mark a "S" in the QSL status field if the field was empty, or it will mark a "X" in the QSL status field if it previously contained a "R". Note that this is the system for tracking QSL status within Log-EQF: S = Sent / R = Received / X = Exchanged QSLs. Finally, if you have the SAM Callsign Database installed, Log-EQF will give you the option to have address labels printed for each QSL label. AUTOMATIC LOGGING PAGE 4.5 - LOG new entries - AUTOMATIC mode -------------------------------- This menu item selects the automatic logbook update function. This mode enables you to enter new entries into the logbook in "realtime", during a QSO. The function is called AUTOMATIC since the Date, Start Time, and End Time for each QSO are taken from the computer clock. If you have the Kenwood radio interface connected, the Frequency and Mode fields are also automatically logged. Below is a view of the Log-EQF AUTOMATIC LOGGING screen: ╒════════════════════════════════════════════╤═════════════════════════════╕ │ CALLSIGN -> ░░░░░░░░░░░░░░░░░░░ │ 16:50:14 12-31-92 (13:50) │ │ ────────────────────────────────────────── │─────────────────────────────│ │ REPORT SENT -> ░░░░░░░░░░░░░░░░░░ │ FUNCTION: AUTOMATIC ENTRY │ │ REPORT RCVD -> ░░░░░░░░░░░░░░░░░░ │ OPERATOR: N3EQF │ │ ────────────────────────────────────────── │ Log-EQF Version 6.0 │ │ NAME -> ░░░░░░░░░░░░░░░░░░░░░░░░░ ╞═════════════════════════════╡ │ CITY -> ░░░░░░░░░░░░░░░░░░░░ │ <F1> Save QSO 2460 │ │ STATE -> ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F2> Log Start Time │ │ COUNTRY -> ░░░░░░░░░░░░ │ <F3> Edit Log: LOGBOOK │ │ ────────────────────────────────────────── │ <F4> Clear Screen │ │ FREQUENCY ->21.134.00░ VFO A ░ 14.147.80 ░ ├─────────────────────────────┤ │ MODE ->CW ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F5> Info on DX Prefix │ │ POWER LEVEL ->100 ░░░░░░░░░░░░░░░░░░░░░░░░ │ <F6> Notepad Entry │ │ ────────────────────────────────────────── │ <F7> Run Another Program │ │ 10-10 -> ░░░░░░░░░░░░░░░░░░░░░░ │ <F8> Terminal / Scrollback │ │ QSL STATUS -> ░░░ QSL Codes: S/R/X/P ░░░░░ │ <F9> PacketCluster (tm) │ │ INFO -> ░ │ <F10> KENWOOD Control │ ╞════════════════════════════════════════════╧═════════════════════════════╡ │W3IXR BBS Enter Command: A,B,C,D,F,H,I,JA,L,M,O,R,S,T,U,V,W,X,Y,?=help> │ │b │ │You have been connected 3mn 55s - Computer-time : 1s │ │73 Tom, and please come back. │ │ │ │*** DISCONNECTED │ └──────────────────────────────────────────────────────────────────────────┘ This view of the logging screen shows a Kenwood transceiver (VFO and MODE display) and a TNC (box on bottom) interfaced to the program. A full-screen display shows entry lines for CALLSIGN, REPORT RECEIVED, REPORT SENT, NAME, CITY, STATE, COUNTRY, FREQUENCY, MODE, POWER LEVEL, TRACK, QSL STATUS, and INFO. These fields may be entered in any order, by using the <Up> or <Down> arrow keys to position the cursor on the desired line. Also, the <Enter> key can be used to step through the lines without affecting any information already entered. AUTOMATIC LOGGING PAGE 4.6 The keyboard edit keys may also be used to make corrections to any of the text already entered, so the entire line does not have to be retyped. Position the cursor on the line to be corrected, then move the cursor over the character desired using the <Left> and <Right> arrow keys. To delete a character, position the cursor over the character and depress the <Delete> key. To insert additional information between characters, depress the <Insert> key and type in the additional characters. You may deselect the insert mode by again depressing the <Insert> key, or it will automatically be deselected when you move the cursor to another line. When the <Insert> function is active, the cursor will change from a square to a single line. The <Home> key may be used to position the cursor back to the beginning of a line when you have already moved the cursor to within the line. The <End> key positions the cursor at the end of current text on any line. Various function keys, plus the <Esc> and <Alt> keys provide control over logbook operations: <F1> is used to save the logbook entry to the disk file, after all logbook information has been supplied. If a valid callsign has not been entered, no action will be taken. When <F1> is selected, the current log clock time is logged as the QSO END TIME. If <F2> had not been selected previously, then the QSO START TIME will be logged as the current clock time also. <F2> is used to LOG START TIME of QSO from the computer clock. When the key is depressed, the current time is logged as start time. Each time <F2> is pressed, the current time will be logged again. This overrides the QSO start time which is entered automatically every time a new callsign is entered. <F3> allows you to update any recent QSO entries in the logbook. This feature can be used during a roundtable QSO to fill in details for any of the stations in the group. <F4> may be selected to clear all information displayed on the screen. When the key is pressed, the program will prompt you to verify you want to clear the screen. If you respond with anything other than "Y" for yes, the entry in progress will not be cleared. <F5> may be selected to lookup DXCC information based on the prefix of the callsign currently entered. The DXCC prefix, country name, CQ and ITU zones, continent, and beam heading are displayed in a box below the Log Keys box. Hitting this key also access the SAM or HAMCALL databases using the current callsign. <F6> is used to enter information into the NOTEPAD for a log entry. The NOTEPAD is located in the window at the bottom of the logging screen. To complete the entry in the NOTEPAD, hit the <F1> key. AUTOMATIC LOGGING PAGE 4.7 <F7> is used to run another program while Log-EQF remains resident in memory. A pop-up menu will appear which presents a choice of running one of the two SHELL programs you specified on the SETUP MENU, a third program or command to execute, or returning to DOS. If you choose to go to DOS, you can execute any DOS commands you like, and when you are ready to return to Log-EQF, just type "EXIT". The Log-EQF log entry screen will reappear, just as you left it. Any other program to be executed from Log-EQF must either be in the current disk directory, in the DOS "PATH", or have a batch file in the current directory to perform a directory change. A DOS program can also be used to "pipe" information back to Log-EQF for display on the logging screen, if it can be made to create a disk file called LOG-EQF.TMP in the Log-EQF directory. An example of this usage is the "GOLIST" QSL Manager program by W6GO/K6HHD. A BATCH file is included (GOLIST.BAT) to show how this can be accomplished. <F8> is used to enter the split-screen TNC terminal emulation. Also, the window at the bottom of the logging screen will monitor activity on your TNC, if you have enabled the TNC option on the SETUP MENU. If you see information scroll past this window, and would like to see the information you missed, use the <F8> key to display the last 20 lines of text. You may even scroll back through previous text by using the <Page Up> key. <F9> is used to access the PacketCluster (tm) screen, which shows the 15 most recent DX spots, along with a window to make your own DX announcement over the PacketCluster. To work a spotted DX station, just position the highlight bar to the corresponding announcement and hit <Enter>. The frequency will be set into your radio automatically if one is interfaced, a DX INFO lookup will occur, and the logging screen will be presented with the callsign entered in the CALLSIGN field. To make a PacketCluster announcement, hit the <F1> key, enter a comment if desired, and hit <Enter>. You must be currently connected to a PacketCluster node in order to make an announcement, of course. See section 7 of this manual for more information about using PacketCluster with Log-EQF. <F10> is used for radio control, and its function depends on the radio in use. If you are using a Kenwood radio, and the Rig-EQF program resides in the same disk directory as Log-EQF, <F10> will run this program. (Rig-EQF is available from N3EQF). If your rig requires the mode and frequency to be manually updated, the <F10> key is used to retrieve mode and frequency info into the logbook. Registered users of Log-EQF receive a program called Mem-EQF, which acts as a disk-based memory system for your rig. Mem- EQF can be activated by the <F10>, <F11> or <F12> keys (see below). AUTOMATIC LOGGING PAGE 4.8 <F11> and <F12> function keys may be used to SHELL from Log-EQF to another program. These two programs are in addition to the ones you specify on the SETUP menu. When you hit <F11>, Log-EQF will run a disk file called SHELL11.BAT. The <F12> key will run a batch file called SHELL12.BAT. You can setup these two files to activate programs you might find useful while logging, such as a grayline map or satellite tracking routine. Edit the two batch files using a text editor, and keep them in the same disk directory as Log-EQF. <Esc> may be used to return to the Main Menu, the same as with the other program screens. You can do this at any time, without losing any of the information currently entered into any of the logbook fields for a new entry. Note that no information in this case will be permanently saved, however, until <F1> is selected to add the entry to the current logbook file. Each time a new callsign is entered into the CALLSIGN field, the logbook is automatically searched to see if that station has been worked before. If it has been, information from your most recent QSO with the station will be entered for you by the program in the NAME, CITY, and COUNTRY fields. <Alt> may be used to control which of the logbook items you want to fill in, instead of using the <arrow> keys to position the cursor on the screen. When you first press the <Alt> key, one letter of each of the logbook items on the screen will be highlighted. If you again press and hold the <Alt> key, and then press the letter key corresponding to the letter highlighted in the item you desire, the cursor will immediately jump to that item. The <Alt> key method of entry described above gives you a faster way to jump from item to item using fewer key strokes. This feature is enabled for both AUTOMATIC and MANUAL log modes, but is not available in CONTEST mode. <Alt-T> is used to start, reset, or turn off a 10-MINUTE IDENTIFICATION REMINDER. This feature is enabled only in the AUTO log mode, and when active it will display at the top of the screen the time remaining until identification is required. After 10 minutes, a visual and aural alert will remind you to identify. The timer will reset automatically every 10 minutes, until you reset or stop the timer by hitting the <Alt-T> keys. <Alt-L> prints an address label if a callsign database system is in use. When this feature is available, Log-EQF will display a message. <Alt-X> switches between AUTO and MANUAL lookup of PREFIX INFO from a callsign. In AUTO, the country/state and beam heading info will be displayed as soon as a callsign is entered. In MANUAL, you must hit the <F5> key for prefix information display. MANUAL LOGGING PAGE 4.9 - LOG new entries - MANUAL mode ----------------------------- The manual logbook entry page may be used to update a logbook "off-line", after the QSO has already taken place. The manual entry mode can be used to enter information into Log-EQF from previous logbooks. ╒════════════════════════════════════════════╤═════════════════════════════╕ │ CALLSIGN ->W1AW ░░░░░░░░░░░░░░░░░░░ │ 16:50:14 12-31-92 (13:50) │ │ ────────────────────────────────────────── │─────────────────────────────│ │ REPORT SENT ->599 ░░░░░░░░░░░░░░░░░░ │ FUNCTION: MANUAL ENTRY │ │ REPORT RCVD ->579 ░░░░░░░░░░░░░░░░░░ │ OPERATOR: N3EQF │ │ ────────────────────────────────────────── │ Log-EQF Version 5.0 │ │ NAME ->JOHN ░░░░░░░░░░░░░░░░░░░░░░░░░ ╞═════════════════════════════╡ │ CITY ->NEWINGTON ░░░░░░░░░░░░░░░░░░░░ │ <F1> Save QSO 2460 │ │ STATE ->CT ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F2> Log Start Time │ │ COUNTRY ->USA ░░░░░░░░░░░░ │ <F3> Edit Log: LOGBOOK │ │ ────────────────────────────────────────── │ <F4> Clear Screen │ │ FREQUENCY ->3.53 ░░ DATE ->27Nov91 ░░░░ ├─────────────────────────────┤ │ MODE ->CW ░░░░░░░░░░░ TIME ON ->02:57:23░ │ <F5> Info on DX Prefix │ │ POWER LEVEL ->100 ░░░░ OFF at -> : : ░ │ <F6> Notepad Entry │ │ ────────────────────────────────────────── │ <F7> Run Another Program │ │ 10-10 -> ░░░░░░░░░░░░░░░░░░░░░░ │ <F8> Terminal / Scrollback │ │ QSL STATUS -> ░░░ QSL Codes: S/R/X/P ░░░░░ │ <F9> PacketCluster (tm) │ │ INFO -> ░ │ <F10> FREQ/MODE from radio │ ╞═════╡ NOTEPAD Entry... Hit <Esc> when done ╧═════════════════════════════╡ │ │ │ John took a few moments to ragchew with me awhile! │ │ │ │ │ │ │ │ │ └──────────────────────────────────────────────────────────────────────────┘ This full-screen entry page is very similar to the AUTOMATIC mode, with the following exceptions: - Additional entry fields are provided for DATE, TIME ON, and TIME OFF. Note that only the numerals need to be entered for date and time, and Log-EQF will insert the ":" in the time and "-" in the date fields. The <F2> function key may still be used, if desired, to put the current UTC clock date and time into the DATE and TIME ON fields. - The <F1> key will save the QSO information as displayed on the page, but will not insert the TIME ON or TIME OFF fields. The date and time information must be entered manually. MANUAL LOGGING PAGE 4.10 - Defaults are provided for the REPORT RECEIVED and REPORT SENT fields for each new QSO entry. If the mode entered is CW or FSK, both fields default to "599". For all other modes the default report is "59". - If the SENT or RECEIVED report fields are changed in format (from "579" to "59", for example) Log-EQF will attempt to set the MODE field to agree. - When the <F4> function key is used to clear the screen, the DATE field will remain at the last values entered. (The POWER, FREQUENCY, and MODE fields will also remain at their last values, just as in the AUTOMATIC entry mode). - The FREQUENCY and MODE fields will not automatically update from the radio when the interface is enabled, but the <F10> key may be used to manually retrieve frequency and mode on the radio into the log fields. EDIT LOG PAGE 4.11 - EDIT an entry - based on callsign --------------------------------- This function is used to make changes to an existing entry in the logbook. When the EDIT item is selected, the program will prompt you to enter part or all of a callsign to be found in the log. Any number of characters may be entered. If you enter a partial callsign, every log entry containing that character pattern in the callsign field will be displayed. If you enter a complete callsign, every log entry for that callsign will be displayed. If only one callsign match is found in the log, the EDIT screen will be displayed immediately. If more than one callsign match occurs, all matching entries are displayed and you will be prompted to enter the entry number to be edited. A number will also be displayed in brackets ( [ ] ) indicating the last "match" located, as a default value. If you depress the <Enter> key, the default log entry will be edited; if you enter another number, that entry will be edited. Once you have selected the entry, the QSO information will be displayed on an entry screen that looks like the MANUAL LOGGING screen. The bottom portion of the screen will show the logbook entry in full detail, as it would be if the VIEW IN DETAIL option were selected. A variety of function key operations are available, as displayed on the right side of the screen. To save an edited QSO, just hit the <F1> key. LOAD LOGBOOK PAGE 4.12 - LOAD QSOs from another logbook ------------------------------ Selecting this menu item will allow you to change the logbook disk file from the current loaded file to another logbook file on the disk, from another disk, or to create a new file. Whatever file name you specify will become the file for which VIEW, EDIT, SEARCH, SORT, or LOG functions operate on. The file which was in use before you selected this menu item will remain on the disk, and will not be acted on in any way until you again specify its name from this item. You may hit <F1> to enter CONTEST mode, or <F2> to enter the CONFIG- URATION SETUP MENU. The <F3> key can be used to display all available log files in the current directory. A prompt will appear at the bottom of this screen so you can enter the logbook filename of your choice. The <F4> key can be used to customize the "TRACK" field for the logbook to be loaded. This field name stays associated with the logbook until you change its name. Hitting the <Esc> key while the LOAD LOGBOOK ENTRIES FROM DISK screen is displayed will return control to the Main Menu, and the logbook file name in use before the item was selected will remain in effect. (See "Loading Logbook Files" in Section 3 of this manual for more info). SORT LOGBOOK PAGE 4.13 - SORT logbook file by any field ------------------------------ This menu item allows you to arrange the currently-loaded logbook file in order based on the field of your choice. A menu page is displayed which lists the fields which may be chosen for a sort: CALLSIGN, DATE/TIME, FREQUENCY, MODE, CITY, STATE, COUNTRY, QSL STATUS, TRACK, or INFO. You may also hit the <Esc> key to leave the Sort Menu and return to the Main Menu. ╒═ Logbook SORT by:═══════════════╕ │ │ │ CALLSIGN │ │ │ │ DATE & TIME │ │ │ │ FREQUENCY │ │ │ │ MODE │ │ │ │ CITY │ │ │ │ STATE │ │ │ │ COUNTRY │ │ │ │ QSL STATUS │ │ │ │ TRACK │ ╘═════════════════════════════════╛ The sort function can be useful in a number of instances. For example, if you are interested in finding all the different countries worked, you can sort the logbook according to the STATE or COUNTRY field. The sorted log can then be printed, and each new country will be easier to spot, since they will appear in alphabetical order. If you enter logbook entries using the MANUAL mode that are earlier QSO's than those already entered, you can sort by DATE/TIME to arrange the logbook in chronological order. SORT LOGBOOK PAGE 4.14 NOTE: The sort program is a very disk-intensive operation. The sort may take considerable time to complete, depending on the size of the log and the speed of the disk drive being used. A running-time display is provided on the screen while the sort is in progress. This sorting method was chosen to accommodate very large log files without requiring massive amounts of memory. When the sort is complete, you will be given the option of permanently saving the sorted logbook. If you choose to save the sorted logbook, it will be maintained in the sorted order the next time you load it from Log- EQF. If you do not permanently save the sorted logbook, Log-EQF will use an index file to display or print logbook entries in the order you chose for the sort. A reminder message will appear at the lower left corner of the MAIN MENU while the temporary sort remains in effect. As soon as you load another logbook, the sort order will be removed, and the original logbook file will remain unchanged. Anytime you permanently save a sorted logbook, duplicate QSOs will be automatically deleted. This can happen when multiple logbooks are merged into one large one. A duplicate QSO is determined by matching callsign, date, and time logged for multiple entries, when the logbook is sorted by the date and time fields. SEARCH LOGBOOK PAGE 4.15 - SEARCH logbook - Print/File/QSL Options --------------------------------------- As the menu item suggests, there are options available for this function. There are three diferent kinds of searches. You can search for a pattern in any field (or two fields) of the logbook, you can search for only the unique patterns in a field, or you can search for only those patterns in a field that match those in a pre-defined table. In addition, you can output the results of any search to another logbook, the printer, screen, or QSL labels. A menu screen is presented for selection of the desired option. The options are as follows: ╒═ SEARCH results output to:══════╕ │ │ │ Disk File │ │ │ │ Screen │ │ │ │ Printer │ │ │ │ QSL Labels │ │ │ ╘═════════════════════════════════╛ (1) Disk File - selecting this option causes the results of the search operation to be stored in a logbook. You will be prompted to enter the log name to be used, and prompted again if the name you enter already exists. If the log exists, you can either APPEND (add) the new search entries onto the end of the old file's entries, or REPLACE the old file completely. (2) Screen - this option displays the results of the search on the screen, using the same format as the VIEW IN DETAIL function. (3) Printer - this option dumps the search results to the printer in the standard logbook format. (4) QSL Labels - this option prints QSL labels from the search results, using the usual format. Once the output option is selected, another menu will be displayed, pro- viding selections for which logbook field is to be searched. After you position the highlight bar to the field you wish to search and hit the <Enter> key, you can begin the search in the selected field by hitting <Enter> again, or you can choose a SECOND field in addition to the first one and then hit <Enter>. If you choose to search two fields, any entry which matches BOTH patterns you enter for each of them will be sent to the output. SEARCH LOGBOOK PAGE 4.16 Certain guidelines for the search apply: - Differences in capitalization will be ignored, unless you select the <F1> MATCH UPPER/LOWER Case option. With this option selected, all fields will be matched only if upper and lower case letters match, exactly as entered. - You can search through all logbooks instead of just the logbook that's currently loaded, by selecting <F2> before the search begins. - To search for empty fields (no information entered) hit only the <Enter> key when prompted to "enter the pattern to be searched for". - You can use "wildcard" characters to perform more accurate searches. The wildcard characters are the same as those used by DOS commands; "?" as a "don't care" position holder for single characters, and "*" as the "don't care" condition for multiple characters. The following examples illustrate the use of wildcards: 1) To search for all callsigns that begin with "N3" as the first two characters, type "N3*" for the CALLSIGN field. 2) To search for all callsigns that end in "EQF", you could type "???EQF" for the CALLSIGN field. If the calls N3EQF, WA3EQF, and N9EQF are in your logbook, they would all be found by the SEARCH. 3) To search for all callsigns with a "3" as the second character, type "?3?????" for the CALLSIGN field. Callsigns beginning with "N3" or "W3" would be found, but callsigns that start with "WA3" or "WB3" would be missed. - NORMAL/CONTEST mode select -------------------------- This menu item is used to switch Log-EQF from a "routine QSO" logbook to a contest logbook and back again. When the item is switched to the CONTEST mode, the program automatically calls a subroutine which is used to select the configuration "rules" to be followed during the contest. When the item is selected when already in CONTEST mode, Log-EQF operation returns to the normal mode. Each time the item is toggled back to the contest mode, the contest setup menu will appear again, and the contest configuration can be modified. Operation of Log-EQF in the contest mode is described in Section 5 of this manual. RUN OR SHELL PAGE 4.17 - RUN ANOTHER PROGRAM ┌─────────────────────── Select SHELL ─┐ ------------------- │ │ │ Run: DX-EQF %C │ │ │ │ Run: GEOCLOCK │ │ │ │ Name another program to run... │ │ │ │ Go to DOS │ │ │ └──────────────────────────────────────┘ This item is selected to execute DOS commands, or run another program, without leaving Log-EQF. The file names you specified when the configuration file was established (see Section 3) will be displayed with these items. When you hit <Enter> to select either of the first two "RUN: " menu items, Log-EQF will attempt to execute the program shown. The program specified must either be in the same directory as Log-EQF, or be accessible in the current DOS PATH. The DOS file COMMAND.COM must also be available in the root directory, or as a DOS environment variable called COMSPEC or SHELL. The third line on the menu allows you to run another program besides those specified on the configuration setup. Simply type the program name and hit <Enter> to run the program. The last line on the SHELL menu is provided so you can temporarily return to the DOS environment. Once you are ready to return to Log-EQF from DOS, type "EXIT", and the Log-EQF Main Menu will appear. If your computer has sufficient Expanded Memory installed, along with the appropriate memory driver software, Log-EQF will automatically place itself in this expanded memory during the shell. The Lotus/Intel/Microsoft Expanded Memory Specification (EMS) requires that you have a memory driver such as EMM386 installed. (The EMM386 driver simulates Expanded Memory using your computer's extended memory). Consult your DOS manual, or your computer's User Guide, for information about EMS. You can quickly check to see if EMS memory is in use by Log-EQF. Just select the "Go to DOS" SHELL menu item. If sufficient EMS memory is available, you will see a message "(EMS in use)" displayed at the top right side of the screen. If you see this message, you have all but about 25K of conventional (lower 640K) memory available to run other programs while Log-EQF remains resident in EMS. You can get some programs to report a message back to the Log-EQF logging screen, by "piping" their output to a temporary disk file called LOG-EQF.TMP, instead of to the screen. Whether this can be accomplished depends on the operation of the other program, of course. File GOLIST.BAT is an example of how to accomplish this. EXIT PAGE 4.18 - SETUP program configuration --------------------------- Selecting this menu item causes the Log-EQF configuration setup menu to appear on the screen. Operation of this setup menu is explained in Section 3 of this manual. - EXIT from program ----------------- This item will cause a message to appear, asking you to confirm that you want to exit Log-EQF, and return to the operating system. If you do not answer "Y" for yes, no action will occur. CONTEST OPERATION PAGE 5.0 5. CONTEST OPERATION --------------------- - INTRODUCTION ------------ The CONTEST mode of Log-EQF provides a quicker way to enter the log exchanges during a contest than the NORMAL mode. It also provides ways to help you determine your score when the contest is over, and generates a dupe check sheet to prove you have no duplicate contacts. (Since duplicates are spotted by the program automatically during the contest, you shouldn't have any dupes anyway!). Log-EQF's CONTEST mode is also very useful for DXpedition or Special Event operations. In CONTEST mode, Log-EQF displays a QSO/hour rate, presents fewer logging fields (less clutter), and will announce those "insurance contact" QSO attempts for the current band and mode. After the event, you can use Log-EQF to print and record the sending of QSL's. This program provides you with several options, which you can choose from the CONTEST SETUP MENU to fit the contest you will be operating. Once you have made your selections (see the following pages), try logging a few "practice" contacts before the contest starts. That way you will have time to change any of the setup parameters without wasting precious time during the event. Try printing the "practice" contest log to be sure it works the way you want it to. Log-EQF is designed so that it can adjust to many different types of contests. You can setup 23 different contest configurations that are selected from a menu. For most contests, the Log-EQF printed log is suitable for submission with your official contest entry. Log-EQF also stores a copy of the Contest Entry Logbook on your disk drive, naming the file the same as the logbook, except it will end in ".TXT" instead of ".LOG". This file is stored in pure ASCII format, which means you may edit it using any Word Processor program. If you need more information on the Contest Entry Logbook than Log-EQF automatically provides, this is a way for you to make changes, and then print the final logbook form to submit with your entry. CONTEST OPERATION PAGE 5.1 - CONTEST CONFIGURATION SETUP --------------------------- When you select the CONTEST mode from the Log-EQF Main Menu, another menu appears on the screen, which contains items specific to contest operation. ┌─────────────────────────────────────────────────────────────────────────┐ │ <F1> Select ANOTHER Contest │ │ Log-EQF CONTEST CONTROL <F2> Make a NEW Contest Setup │ │ <Esc> EXIT Menu and SAVE Setup │ └─────────────────────────────────────────────────────────────────────────┘ ╒═══════════════════════════════════════════════╕╒ Band Digital Phone ╕ │ ││ 160 Mtrs 2 0 │ │ CONTEST NAME─> ARRL 160-Meter ││ 80 0 0 │ │ ││ 40 0 0 │ ╘═══════════════════════════════════════════════╛│ 20 0 0 │ ╒═══════════════════════════════════════════════╕│ 30 0 0 │ │ ││ 20 0 0 │ │ LOGBOOK NAME─> ││ 17 0 0 │ │ ││ 15 0 0 │ │ Number of QSO's PER PAGE─> 50 ││ 12 0 0 │ │ ││ 10 0 0 │ │ Keep Separate BAND/MODE DUPE SHEETS (Y/N)? Y ││ 50 MHz 0 0 │ │ ││ 144 0 0 │ │ REPORT for SENT exchange─> 599 WPA ││ 222 0 0 │ │ SERIAL NUMBER as part of exchange (Y/N)? N ││ 432 0 0 │ │ ││ 902 0 0 │ │ Default REPORT for RCVD exchange─> 599 ││ 1296 0 0 │ │ MULTIPLIER FIELD, if required─> SECTION ││ 2304 0 0 │ │ ││ 5760 & UP 0 0 │ ╘═══════════════════════════════════════════════╛╘════════ POINTS PER QSO ╛ Once the contest setup is completed, you will be returned back to the Main Menu. You may return to the contest setup menu to change any contest parameters by switching to NORMAL mode, then back to CONTEST mode from the Main Menu. CONTEST OPERATION PAGE 5.2 Below is a description of each parameter available from the contest setup menu: (1) Contest NAME. The title you enter here will be used on the contest logbook and dupe sheet printouts, and will also be automatically entered in the INFO field of each entry in the contest log. (2) Contest LOGBOOK NAME. The name entered here will be used as the default logbook name for the contest. The logbook name may have no more than 8 characters. (3) Number of QSO'S PER PAGE on printed results. Enter the number here depending on the contest rules. (4) POINTS for each DIGITAL QSO. The values entered for each band will be automatically entered on the logbook printout after the contest, for each non-duplicate CW or FSK QSO, and totalled at the end of the log printout. (5) POINTS for each PHONE QSO. Enter the points to be earned for phone QSO's. As above, the score will be calculated for QSO points based on the number provided here. NOTE: If "0" is entered for BOTH the above POINTS items, the logbook will be printed with only "____________" under the QSO POINTS column, to allow for manual scoring, if desired. CONTEST OPERATION PAGE 5.3 (6) Does each band worked require a SEPARATE DUPE SHEET? If a "Y" for yes is entered here, Log-EQF will keep track of the band and mode for each station worked. The same callsign worked on different bands and modes will therefore not be flagged as a duplicate. If a "N" for no is entered, you will be alerted each time you enter a callsign which has already been worked, regardless of the band or mode. Only one logbook file will be created for the entire contest, no matter which option you choose for this item. (7) Enter the default REPORT to be SENT for exchange. The default report will appear on the log entry screen for each QSO, and may be over- typed as needed. (Again, "default" means that the report displayed on the screen will be logged if you don't change it). (8) Is there a SERIAL NUMBER sent as part of exchange? If you enter "Y" for yes, an automatically-incremented number will be appended to the SENT report for each QSO (and displayed on the logbook entry screen). (9) Enter the default REPORT to be RECEIVED for exchange. This default report will appear on the log entry screen for each QSO, and may be over-typed as necessary. (10) Enter MULTIPLIER FIELD title for RECEIVED exchange. If a title is entered here, an additional field will be available on the contest log entry screen. This field may be used to log the part of the received exchange that counts towards multiplier points, which will make scoring easier after the contest. Anytime a contest requires a longer receive report than the RECEIVED field can hold, use this field to accept the information, with a length up to 12 characters. If the MULTIPLIER FIELD is selected, it will be placed on the entry screen just below the CALLSIGN field. The MULTIPLIER field should usually be the one most likely to change with every QSO, while the REPORT RECEIVED field will usually be the same (59 or 599) for every QSO. If possible, limit the MULTIPLIER FIELD to that part of the contest exchange which will be used to calculate the score. For instance, many ARRL contests use the ARRL SECTION for a multiplier, with the total sections worked being multiplied by QSO points for the final score. In this case, the MULTIPLIER FIELD should be called SECTION, and Log-EQF will calculate the total number of unique sections logged. CONTEST OPERATION PAGE 5.4 - OPERATION DURING THE CONTEST ---------------------------- The basic operation of Log-EQF during a contest remains similar to the "normal" mode, except that certain features are streamlined for faster operation, and some new features appear. ╒════════════════════════════════════════════╤═════════════════════════════╕ │ CALLSIGN ->KH6BR ░░░░░░░░░░░░░░░░░░░░░ │ 16:50:14 12-31-92 (13:50) │ │ ────────────────────────────────────────── │─────────────────────────────│ │ MULTIPLIER -> ░░░░░░░░░░░░░░░░░░░░░ │ FUNCTION: DX / CONTEST │ │ REPORT RCVD ->25 ░░░░░░░░░░░░░░░░░░░░░ │ OPERATOR: N3EQF │ │ ────────────────────────────────────────── │ Log-EQF Version 6.0 │ │ REPORT SENT -> ░░░░░░░░░░░░░░░░░░░░░ ╞═════════════════════════════╡ │ SERIAL NUMBER ->101 ░░░░░░░░░░░░░░░░░░░░░ │ <F1> Save QSO 2460 │ │ ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F2> Printer ON │ │ ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F3> Edit Log: LOGBOOK │ │ ────────────────────────────────────────── │ <F4> Clear Screen │ │ FREQUENCY ->14.070.91 ░ VFO A ░░░░░░░░░░░░ ├─────────────────────────────┤ │ MODE ->CW ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F5> Info on DX Prefix │ │ POWER LEVEL ->100 ░░░░░░░░░░░░░░░░░░░░░░░░ │ <F6> Notepad Entry │ │ ────────────────────────────────────────── │ <F7> Check Partial Call │ │ BAND: 20 Meter CW ░░░░░░░░░░░░░░░░░ │ <F8> Terminal / Scrollback │ │ SINCE LAST QSO: 0:03:21 ░░░░░░░░░░░░░░░░░ │ <F9> PacketCluster (tm) │ │ LAST 10 QSO RATE: 56 /hr ░░░░░░░░░░░░░░░░░ │ <F10> Kenwood Control │ ╘════════════════════════════════════════════╧═════════════════════════════╡ (1) Different LOG screen fields. Probably the most important changes are on the LOG-AUTOMATIC and LOG-MANUAL entry screens. No matter what selections you made when you setup the contest configuration, you will see fewer lines for information entry on the screen. The NAME, CITY, STATE, COUNTRY, POWER, and QSL lines do not appear in contest mode. If you elected to use the MULTIPLIER field option when you configured the contest, the title entered from the configuration menu will appear on a separate line just above the REPORT RCVD line. The information you enter here is automatically appended to the REPORT RECEIVED information when the contest logbook is printed. The MULTIPLIER field information is kept separate within the program's logbook data file. (2) Automatic SERIAL NUMBER generation. If you selected the option to create SERIAL NUMBERS for the contest exchange, a 3-digit serial number will appear below the REPORT SENT line. This number will be automatically incremented after each new QSO is logged, and will be appended to the REPORT SENT information. CONTEST OPERATION PAGE 5.5 (3) Realtime PRINT of each QSO. On the screen's LOGBOOK KEYS menu, key <F2> controls the status of the printer during the contest. If you toggle <F2> to get the printer "ON" message, the printer will output the complete exchange every time you log a QSO. This feature is not intended to generate a "presentable" contest logbook, but is provided as a safety feature, in case Murphy decides to strike your computer system in mid-contest! If you have a printer connected, I highly- recommend you use this option. (4) DUPE CHECKING. A dupe-check routine runs each time you enter a call. If a duplicate is found, you will be greeted with an audio "raspberry", and a corresponding message will appear. Note that you always have the option of logging this contact anyway, even if it was found to be in the log already. A duplicate callsign will not be reported as a dupe, as long as that call was not logged on the current band and mode. The current band and mode (either DIGITAL or PHONE) will be displayed on the screen for you, so that you can be sure the log agrees with your current radio mode and frequency. If you are using a radio interface, this display will be updated automatically as you change radio parameters. (5) PARTIAL CHECK. This feature allows you to check part of a callsign to see any callsigns in the log which could possibly match. For instance, if you copy only "ABC" as the callsign, hitting the <F7> key would display any calls ending in "ABC" which were worked already. (6) QSO RATE and LAPSE TIME DISPLAY. A box will be displayed to give you progress information during the contest. A running timer shows how much time has passed since the last QSO was logged. Another display will track the rate (in QSO's per hour) of your last 10 QSO's. This rate display will become active once you log more that 10 contacts. CONTEST OPERATION PAGE 5.6 - OPERATION AFTER THE CONTEST --------------------------- IMPORTANT: Always make a backup copy of your contest data files before attempting to generate dupe sheets or log forms, in case something goes wrong! Anyone who has worked with computers for long will tell you it can and does happen eventually! Several Main Menu items change their title and function when in the contest mode of operation: (1) PRINT contest entry logbook. This is the menu item used to generate the logbook which is to be submitted with your contest entry. This item also generates a disk file in true ASCII format, which contains the same information as is printed. (2) Run and Print DUPE CHECKSHEET. This menu item will create a duplicate checksheet for each band/mode combination in the contest log. If you selected "N" for the CONTEST SETUP MENU item concerning separate dupe sheets for each band, only one dupe sheet will be created. It will flag duplicate contacts based on callsign alone, so if the same station is worked on different bands, it will be marked as a duplicate. You will be given the option to print multiple copies of the DUPE CHECKSHEET, and to create ASCII disk files from this same information. Some of the parameters which affect the contest logbook printout are controlled from the contest configuration menu. You can alter any of these parameters after the contest is over, in order to change the appearance of the printed log. The number of QSO's per page, and the number of points for each type of QSO, will change only the printed logbook, not the contents of the logbook data file itself. (2) Run and print DUPE CHECKSHEET. This operation is controlled completely by Log-EQF. All that is required is that you load the logbook data file for the contest being duped, select the Main Menu item, and wait until prompted to turn on the printer. The printed dupe-sheet is formatted to fit on 8-1/2 x 11 inch paper, and will be automatically numbered and titled, with duplicates marked. The number of valid QSO's (not duplicated) will also be printed at the bottom of the last page. Again, a true ASCII file will be created on the disk. RADIO INTERFACE OPERATION PAGE 6.0 6. RADIO INTERFACE DESCRIPTION ------------------------------- Interfacing a computer-compatible radio to your computer introduces some very convenient features to the Log-EQF program. Connecting the radio to your computer requires a 3-wire (minimum) cable between one of your computer's serial (COM) ports and the radio interface. Some radio models have the interface built in, while others require an external level converter. Please consult the appropriate manual for the specifics on your radio. NOTE: If your radio requires an RS-232C level converter, you can build one easily, and for much lower cost, than the commercial units. An excellent construction article written by Wallace R. Blackburn, AA8DX, appeared in February 1993 QST. The article describes a simple circuit you can build using a handful of readily-available components. Once the hardware connecting the radio and computer is operational, Log-EQF requires a software configuration to tell it how the processor in the radio exchanges information with the computer. In an ideal world, all radio manufacturers would use the same interface specification, all rigs would understand the same instructions, and the data transmitted from the radio to the computer could be interpreted in the same way. In the real world, even different models by the same manufacturer are sometimes not compatible with each other! This is where the "programmable radio interface" section of Log-EQF comes into play. Log-EQF uses the information in disk files ending in ".RIG" to supply it the information about the radio connected to the serial port. The files which exist for specific radios are made available for selection from Log- EQF's SETUP menu. Each file contains 40 lines of information, with each line representing a parameter which affects the way Log-EQF handles communication with the radio. If your radio is "computer-ready" but no .RIG file exists for it, you can create a new file using a text editor. The easiest way to do this is to copy an existing file for a similar radio to a new file, then edit the new file with the appropriate information. The parameters in the file are divided by function, and must remain in order. Values for each parameter must begin on column one of the file, with any comments about the parameter positioned to the right of an exclamation point (!). If you create a new radio file and the program doesn't seem to work right with the radio connected, don't be surprised or discouraged. There are a lot of parameters involved, and any one of them can be the source of trouble if not correct. Analyze the symptoms carefully, and look at only those file parameters which seem directly related (use my cryptic comments next to each parameter as a guide). If neither the frequency or mode are displayed on the AUTOMATIC logging screen, and typing frequency or mode has no effect, check the communication parameters like baud rate, data and RADIO INTERFACE OPERATION PAGE 6.1 stop bits, etc. first. If those are correct, check the parameters near the top of the .RIG file. If some operations work but others don't, concentrate only on the parameters grouped in the inoperative section of the .RIG file. Remember to return to the Log-EQF SETUP menu each time you change the .RIG file, so the changes you make are read by the program. If you develop a .RIG file for a new radio, please help other users by sending N3EQF a copy of the file. EXAMPLE RADIO CONFIGURATION FILE: --------------------------------- Icom IC-735 ! Model for display within Log-EQF --FIRST LINE IN FILE-- 0.0 ! Update rate in seconds - or (M) for manual or (N) for none ! Acknowledge command, if required 6 ! Bytes received from radio for ECHO or OK block ! Pacing or Initialize command, if required H ! Hexadecimal (H) or String (S) instruction data type F ! Commands sent to radio Forward (F) or Reverse (R) order ! -------------- FREQUENCY READ ------------------------- FEFE04E003FD ! Command to receive operating FREQUENCY from radio 10 ! Number of bytes expected from radio after FREQ command 6 ! Starting byte position for FREQUENCY value 4 ! Number of bytes in FREQUENCY value R ! Frequency decoded in Forward (F) or Reverse (R) order B ! BCD (B) or Weighted Binary (W and scale) or BCD single (S) ! -------------- MODE READ ------------------------------ FEFE04E004FD ! Command to receive operating MODE from radio 7 ! Number bytes expected from radio after MODE command 6 ! Starting byte position for MODE value 1 ! Number of bytes in MODE value ! Bit mask for MODE value, if required 03 ! Value for CW 00 ! Value for LSB 01 ! Value for USB 05 ! Value for FM 02 ! Value for AM 07 ! Value for FSK ! -------------- FREQUENCY SET -------------------------- FEFE04E00500000000FD ! Command to set the operating FREQUENCY 6 ! Starting byte position for FREQUENCY value 4 ! Number of bytes in FREQUENCY value ! -------------- MODE SET ------------------------------- FEFE04E00600FD ! Command to set the operating MODE 6 ! Starting byte position for MODE value 1 ! Number of bytes in MODE value 03 ! Value for CW 00 ! Value for LSB 01 ! Value for USB 05 ! Value for FM 02 ! Value for AM 07 ! Value for FSK RADIO INTERFACE OPERATION PAGE 6.2 RADIO CONTROL AND DISPLAY OPERATION: ----------------------------------- Control and display of radio frequency and mode is available on the AUTOMATIC logging screen. If the frequency or mode of the radio are changed at the radio, Log-EQF will read and display the updated information. When a QSO entry is saved into the logbook, the frequency and mode displayed on the screen are automatically entered into the log as well. To control the radio frequency and mode from Log-EQF, just type the desired value into the FREQUENCY or MODE field. NOTES: 1). Some radios do not support all of the required interface instructions instructions for complete exchange of frequency and mode. For example, some radios cannot send information to the computer, but do allow control of frequency or mode from the computer. Other radios send only information from a VFO specified by the computer instruction, instead of reporting the selected VFO. For these radios, the VFO must be selected at the rig in order for the computer to receive the frequency and mode. 2). Some radios "hang up" all radio functions while transferring information between it and the computer. For this reason, it is not practical to perform these transfers automatically at a given time interval. For these rigs, specify an "M" for the update rate. A function key <F10> will be dedicated to retrieving the mode and frequency from the radio into the logging fields. 3). Some radios cannot process data at high speeds, and may require a delay between characters sent from the computer. Specify a number between 1 and 5 as the second parameter in the "update rate" line of the .RIG file, to cause 1-tenth to 5-tenths of a second delay between characters. A comma must separate the two items on this line; for instance a manual update with a 0.3 second delay between characters would be specified as "M,3". 4). A scale factor can be specified to calibrate frequency display received from the radio. If the displayed frequency is 0.7 instead of 7.0, for example, you can specify a scale factor of 10. The scale factor is the second parameter on the frequency read "type" line in the .RIG file. For example, a radio requiring BCD frequency decode and a scale factor of ten would need the line "B,10". RADIO INTERFACE OPERATION PAGE 6.3 KENWOOD ADDITIONAL CONTROL FEATURES: ----------------------------------- When a Kenwood radio is attached to your computer's COM port, control and display of certain parameters is enabled on the AUTOMATIC logging screen. The following additional functions are available only for Kenwood radio control: <PgUp> These keys may be used to control the radio VFO by slewing <PgDn> frequency up when <Pg Up> is pressed, and down when <Pg Dwn> is pressed. The tuning rate begins in 10 Hz increments, then switches to 100 Hz, and finally switches to 1 Khz if the key is held down. Once the key is released for a second, the rate resets to the slow 10 Hz tuning step. <F10> The <F10> function key causes the optional Rig-EQF radio control program to "pop up". Rig-EQF provides advanced control features, including local memories, programmable scanning, and a large frequency display. Rig-EQF is available as shareware from N3EQF. <Alt>-V is used to switch between VFO A and VFO B. The current VFO is displayed to the right of the current frequency. The opposite VFO frequency is also displayed, to the right of the current VFO display. TNC OPERATION PAGE 7.0 7. TNC OPERATION WITH Log-EQF ------------------------------ Log-EQF operates as a generic communications program, or "dumb terminal", for use with any TNC capable of software control via an RS-232C interface. Log-EQF communicates with your TNC through the COM port you specify from the CONFIGURATION SETUP menu. The baud rate used for communication between the TNC and your computer must also be entered on the CONFIGURATION SETUP menu. If your TNC uses automatic baud rate control, it should be disabled and set to a baud rate which matches the rate you select from Log-EQF. The most common problem with communication between Log-EQF and TNC's concerns the use of HOST mode. Some programs designed for specific TNC models use the HOST MODE; a special protocol that does not accept typed commands. If your TNC is initialized by any program that operates via host mode, you must return the TNC to the "dumb terminal" mode before running Log-EQF. Some TNC communications programs have an option to set for "Host on exit". This option should be disabled, so that your TNC returns to "dumb terminal" or "command" mode once the program terminates. Some TNC's can be switched into command mode by typing three <Ctrl-C> characters quickly in succession. NOTE: Commands vary between models of TNC's, so no attempt to specify TNC commands will be made in this document. Please consult the documentation for your specific TNC to find the applicable commands. Other communications parameters related to TNC operation are Parity, Data Bits, and Stop Bits. Your TNC must be set to match the parameters you set on the Log-EQF SETUP MENU. The defaults are No Parity [N] (this may also be Even [E] or Odd [O] Parity), 8 Data Bits, and 1 Stop Bit. When you enable the TNC control by specifying a COM port and a baud rate from the Log-EQF CONFIGURATION SETUP menu, TNC control is selected by use of the following keys on the MANUAL and AUTOMATIC logging screens: <F8> This key may be used to select the split-screen terminal emulation. This is the screen you will use to TRANSMIT data over the TNC, or to monitor received TNC data when not logging a contact. Additional features for TNC control are also accessed from this screen, including file transfer and dumping TNC output to your printer. <F9> This key presents the PacketCluster (tm) DX Spot screen. When you monitor the PacketCluster and DX announcements are received, the previous 15 spots will be displayed on this screen. To work a station displayed on the screen, move the highlight bar to the station you wish to work, and hit <Enter>. Log-EQF will return you to the logging screen, with the DX stations's callsign and the spot frequency automatically entered into the log. If you have a radio interfaced to your computer, the radio will also be placed on the correct frequency. TNC OPERATION PAGE 7.1 FILE TRANSFERS -------------- When TNC communication is enabled, Log-EQF may be used to transmit (upload) or receive (download) ASCII files. This operation is available only on the split-screen TNC CONTROL screen, accessed from the logging screens. Two keys on the TNC CONTROL screen are used to perform file transfers: <F3> This key is used to RECEIVE, or download, the information being received from the TNC into a disk file. Log-EQF will prompt you to enter the name of a disk file. If the file you name already exists, Log-EQF will ask you if you want to overwrite it or append to it. Make sure you aren't about to eliminate a disk file you need before electing to replace it! To end the download, hit the <Esc> key. Log-EQF will continue to store information into the file until you do this, or when you run out of room on your disk! <F4> This key is used to TRANSMIT, or upload, a file to a connected station or BBS. If you are running PACKET, establish the connection before initiating the upload. If the file to be transmitted contains any non-displayable characters (such as in an executable program file) you must also be in TRANSPARENT mode. Log-EQF will prompt you for the name of the file to be sent when you first hit <Page Up>. The transmission will begin as soon as the program locates the disk file you specify. You may hit the <Esc> key to end a file transmission, or wait for the end of the file when Log-EQF will return to the normal TNC CONTROL screen operation. TNC OPERATION PAGE 7.2 MACRO KEYS ---------- The function keys <F5> through <F10> may be programmed for use as macro keys. (A macro is a way to combine steps or text into a single file so you don't have to type as much). You may setup the macro keys to execute commands for your TNC, such as a single-key "HELP" function. Macro keys may also be created to playback information such as contest CQ's or exchanges, or with information like your name and QTH that you often transmit over CW or RTTY. Macro information is contained in disk files called 5.KEY through 10.KEY, which you create using a text editor. Make sure the editor you use does not insert any special characters for formatting. There are only a few "rules" to follow in creating macro files: 1. Log-EQF will output a carriage return at the end of each line of text in the file. This means if your macro file contains only the word HELP, Log-EQF will output HELP followed by a carriage return character. 2. If you want to output a "control character" (one which is formed by holding down the <Ctrl> key) to your TNC, you may use the "^" character in the macro file. For example, if you need to output a <Ctrl-C> character to the TNC, you would type "^C" in the macro file. 3. A carriage return may be inserted into a macro file by using the text: "<CR>". 4. An "escape" character may be inserted into a macro file using the text: "<ESC>". Some example macro files have been included with Log-EQF. The <F5> key is setup to force certain parameters to "normal" conditions for use with Log- EQF, such as ECHO ON and BKONDEL ON. You can expand this file to restore proper TNC operation for your configuration. This can be useful when switching between Log-EQF and other terminal programs which might set your TNC to different parameters automatically. NOTE: The <F11> and <F12> function keys can also be used on the TNC screen. These "hot keys" cause a SHELL from the Log-EQF TNC screen to the program or commands specified in two BATCH files, called SHELL11.BAT and SHELL12.BAT. You can customize the two files to suit your needs, using a text editor. TNC OPERATION PAGE 7.3 PACKETCLUSTER ------------- To use PacketCluster (tm) with Log-EQF, just connect to a node on the cluster from the TNC CONTROL screen. When you return to either the MANUAL or AUTOMATIC logging screens, Log-EQF will display PacketCluster activity on the bottom 6 lines of the logging screen. To make a PacketCluster DX announcement, hit <F9> from the logging screen. You will be presented with the PacketCluster screen, which shows the last 15 DX spots received, and permits you to send a DX spot to other stations on the cluster. Hit the <F1> function key to announce DX. If you have already entered a callsign on the logging screen, it will be entered automatically for the DX spot. If you are using a radio interface, the current frequency will also be entered automatically. You need only enter a comment, if desired, and hit the <Enter> key to send the DX announcement. If either the callsign or frequency were not entered, you must supply that information before hitting <Enter>. Other PacketCluster transmissions, not in the DX spot format, must be made from the TNC CONTROL screen. If you do not intend to make any transmissions over the PacketCluster, you do not need to connect to a cluster node. Log-EQF will still monitor DX announcements from other stations, and post the last 15 spots on the PACKETCLUSTER screen. CW KEYER PAGE 8.0 8. CW KEYER ------------ Log-EQF contains a CW memory keyer that can be used to key your transmitter from your computer's serial (COM) or parallel (LPT) ports. A simple interface between your rig and computer is all that's required. Usually, the interface consists only of a resistor and NPN transistor to switch the rig's key input from either the LPT port STROBE or the COM port DTR signal lines. This is the same interface required by other popular logging programs such as NA and CT. Schematics for simple keyer interfaces are available from N3EQF. The computer port to be used for transmitter keying is selected from the SETUP menu. To activate the CW KEYER from the LOGGING screen, just hit the <ALT-K> key combination. A popup menu will appear which shows all the keyer controls. The keyer is controlled as follows: Function keys <F1> through <F6> send the messages in memories one through six. Function key <F7> can be used to "type-ahead" a message. This gives you the ability to enter a message while listening to the other station, and make corrections to the message before it is sent. The message can be as long as 75 characters, and will be transmitted when you hit the <Enter> key. This message will not be stored for later use. Keys <F8> and <F9> are used to decrease and increase key speed. Speed is variable from 10 to 50 words per minute (WPM). The <F10> key is used to store messages into the six memories. These memories are stored into a disk file so they are maintained between logging sessions. When you hit <F10>, Log-EQF will ask which memory is to be stored. Enter a number between 1 and 6, and then type the message you want to store. A special character combination can be used to insert a CALLSIGN into a CW memory message. Anywhere the "%C" characters appear in a memory message, the current CALLSIGN appearing on the logging screen will be inserted. Likewise, "%N" will insert the NAME, or the SERIAL NUMBER if in contest mode. Some CW abbreviations are assigned to different characters on the keyboard: SYMBOL ABBREVIATION MEANING ------ ------------ ------- : AR End of Message ; AS Standby < SK End of Transmission > KN Invitation to Transmit = BT Break or Pause @ SN Attention EXTERNAL CONTROL PAGE 9.0 9. EXTERNAL CONTROL VIA LPT PORT --------------------------------- You can use Log-EQF to control an external device connected to a parallel (LPT) port of your computer. The control consists of 8 data lines which are turned "off" and "on", either manually or automatically by the software. The data lines of a standard PC parallel interface card are TTL levels, and so can be easily used to switch low-current devices. A simple circuit diagram that can be tailored to control many devices (voice keyers, antenna switches, etc.) is available from N3EQF. Also, the port can be controlled in a "CT" program emulation mode, so antenna switches and other products that are sold as compatible with the "CT" program will work with Log-EQF as well. Three methods of controlling the eight LPT port data lines are available. The <Alt-E> key combination while on the LOGGING screen displays a popup menu which can be used to control the port. Function keys <F1> through <F3> are used to select the mode of port operation. Method one is allows each of the eight LPT port data lines to be selected individually. After hitting <F1>, you enter a number between 1 and 8 to turn on a single data line. You can turn all the 8 data lines off by entering the number "0". The second method of controlling the eight data lines is automatically, based on the frequency entered in the FREQUENCY field while logging. This frequency-based control is activated by hitting the <F2> FREQUENCY TABLE function key from the popup menu. The frequency ranges used to switch the port lines must be setup in a file called LOG-EQF.FRQ. This file is an ASCII text file that can be modified with any text editor. Each of the first eight lines in the file represents the frequency range which will activate each of the eight data lines. There must be two numbers on each line of the file, separated by a comma. The first number is the lower frequency limit, and the second number is the upper frequency limit. Once the LOG-EQF.FRQ file is setup, Log-EQF will switch one of the eight lines on when the current log frequency is within the specified range. The third method is actually a "hybrid" mode, since it combines both automatic and manual selection of the LPT data lines. The <F3> function key enables this "CT emulation" mode, which uses outputs 1, 6, 7, and 8 as a BCD (binary coded decimal) drive for antenna switching based on the current frequency band, and outputs 2 through 5 as manual selections for voice keyers or other accessories. Outputs 2 through 5 are selected manually by entering a number in this range from the menu screen. The band outputs use the following BCD codes: 160 80 40 30 20 17 15 12 10 Meters --------------------------------------------------------- 1 2 3 4 5 6 7 8 9 BCD code The LPT port external control is enabled on the Log-EQF SETUP menu. LIBRARIES PAGE 10.0 10. MAINTENANCE OF THE DX PREFIX AND STATE LIBRARIES ----------------------------------------------------- The DX Prefix Library is a disk file called PREFIX.LIB, which is accessed by Log-EQF whenever the <F5> function key is depressed from the Automatic or Manual LOG ENTRY screens. The file contains a list of possible callsign prefixes, with corresponding DXCC prefixes, ITU zones, CQ zones, ITU continents, and Latitude/Longitudes for each. Since the DXCC country list changes fairly often, it will probably be necessary to update the prefix file from time to time. It is extremely important that the format of the library file is not changed if you edit it, or the file cannot be read by Log-EQF. The information in the file must be aligned in the proper column, or an error will occur when the program tries to read entries from the library. If you are a REGISTERED USER of Log-EQF, you can use the utility program called DX-EQF to edit the PREFIX.LIB library file. Activate DX-EQF and access the "<F5> LIBRARY" feature. You may then follow the prompts to add, delete, or modify the entries in the library. DX-EQF will take care of all the details (outlined below) to organize the library file. See Chapter 10 of this document for details on operating DX-EQF. LIBRARIES PAGE 10.1 If you decide to edit the library file without the assistance of the DX-EQF program, you must use an editor which does not add any control characters to the text. The only non-printable character which may reside in the library file is the carriage return, following each line of text. The following rules apply to the file format: 1) Each line in the file must have exactly 80 columns in following format: 1-----6--------14-------------38------52------66------69------74-----80 ^ ^ ^ ^ ^ ^ ^ ^ Prefix Country Name CQ Zone Latitude DXCC ITU Zone Continent Longitude The "ruler" above shows the column number where the file data must begin. As long as you line up the information you add or change with the rest of this file's information, you should have no problem. 2) Longer Prefixes must precede shorter ones which have the same characters. For example, "ZL7" must occur ahead of "ZL", or else ZL7ABC would be incorrectly reported as New Zealand, instead of Chatham Island when the library is searched. 3) If more than one DXCC prefix exists for a single callsign prefix, the DXCC prefix must be preceded by an asterisk ("*"). For example, since both Bouvet and Peter Island are recognized by the "3Y" prefix, the following two lines are present in the file: 3Y *3Y/B Bouvet 67 38 AF -54 3.4 3Y *3Y/P Peter Is. 72 12 AN -69 -90.6 4) Please note the sign conventions for Latitude and Longitude. Latitude is positive if it is North, and Longitude is positive if it is East. LIBRARIES PAGE 10.2 A second file called STATES.LIB is searched anytime you hit <F5> and you have already entered something into the STATE log field. If a match is found with the STATE you have entered, the BEAM HEADING display will be updated for the corresponding location. Also, there is an optional field in the STATES.LIB file, which can be used to display whatever you choose whenever this STATE match occurs. You could, for instance, edit the STATES.LIB file to include the ARRL SECTIONS for each state or province. You may edit the STATES.LIB file to customize it, as long as you follow these rules: 1) Each line in the file must have the following format: STATE, Latitude, Longitude, Optional Comment 2) If you do not supply an "Optional Comment", the last character on each line of the file must be a comma (","). 3) Latitudes and Longitudes follow the same format as for the DXPREFIX.LIB file. Latitude is positive if it is North, and Longitude is positive if it is East. Always make a backup file before editing the library files, in case some- thing goes wrong! IN CASE OF TROUBLE PAGE 11.0 11. IN CASE OF TROUBLE ----------------------- Every effort has been made to provide a bug-free program, but as with any software, there may be combinations of events which cause problems. Below are some suggestions for locating the source of problems with Log-EQF should they occur: (1) PROBLEM: Log-EQF "hangs-up" the computer; no error messages are displayed, and no way to recover use of the computer until it is "re-booted". - Check to see if there are any memory-resident ("TSR") programs running at the same time as Log-EQF. One way to verify this is by listing your AUTOEXEC.BAT and CONFIG.SYS files, to see if any programs are being activated automatically when your computer is started. Some programs can interfere with other program operation. If there are any programs of this type on your machine, try removing them temporarily and running Log-EQF by itself. It is also possible that the parameters stored in file Log-EQF.CNF are not valid. Try deleting the file from your disk and then run Log-EQF again. The program will create a new configuration file with default values when you start it. (2) PROBLEM: With a radio interface installed, no radio control operations function. - Check the SETUP menu and verify all parameters match the radio and COM port being used. In cases where your radio model does not have an existing *.RIG file, you will need to create or modify an existing file to match the parameters specified by the rig's manufacturer. Consult the users guide for your radio and interface, and section 6 of this manual for more information. (3) PROBLEM: Attempts to SHELL to DOS or another program are unsuccessful. - Log-EQF requires the DOS file COMMAND.COM to be installed in the root directory of the same disk as this program, or that either of the DOS environment variables called COMSPEC or SHELL are specified. A typical method of correcting this problem is to add the following statement to your AUTOEXEC.BAT file: SHELL=C:\DOS\COMMAND.COM Consult your DOS manual for more information about SHELL. IN CASE OF TROUBLE PAGE 11.1 (4) PROBLEM: Log-EQF displays the Main Menu with a message "ERROR CODE xx" at bottom of the screen. - There are various routines which attempt to recover from most error situations within Log-EQF. If you see the above message, with an error number in place of "xx", then an error occurred which can not be recovered. This can only happen if Log-EQF encountered a situation for which the program does not provide recovery action. - If you find you are getting errors under certain conditions, try to isolate the problem by retracing your steps. If you cannot resolve the problem in this manner, please write or call for technical support using the information at the front of this manual. (5) PROBLEM: A logbook data file cannot be loaded successfully by Log-EQF. - There is always the possibility that your data file has been corrupted, either accidently from an incorrect DOS command, or as a result of a power glitch or some other interruption during a disk save operation. Log-EQF creates a backup file regularly when you perform an edit, sort, or search-with-output-to-the-disk operation. The backup file's name is always "xxx.BAK", where xxx is your logbook file name. To load from a backup file, just type the DOS command "COPY xxx.BAK xxx.LOG", where again xxx is the logbook name, and then start up Log-EQF. (You should create regular backups using the BACKUP option on Log-EQF's LOAD LOGBOOK menu). - A utility called FILE-EQF is available to registered users of Log-EQF, which provides a routine which attempts to recover damaged logbook files. FILE-EQF also can be used to convert between Log-EQF files and other file formats, including dBASE, ASCII, CT, and NA. (6) PROBLEM: When printing logbooks or QSL labels, "funny looking" characters are printed instead of lines. - Check the setting for <F2> PRINTER TYPE on the SETUP menu. If it is setup for "GRAPHICS", hit <F2> again until "STANDARD" is displayed. (7) PROBLEM: QSL Labels will not line up with proper spacing using a laser printer. - Check to be sure your laser printer is setup for 6 lines per inch, or 60 lines of text on a 10-inch page. Other programs may send control codes to your printer to control font size and spacing, so you may have to manually set your printer. Top and left margins can then be adjusted from Log-EQF to align the first label on the page.